How To Reset Water Filter Whirlpool Fridge?

How to Reset Water Filter Whirlpool Fridge?

Your Whirlpool refrigerator’s water filter helps to keep your water clean and free of impurities. However, over time, the filter can become clogged and stop working effectively. When this happens, you’ll need to replace the filter.

Replacing the filter is a simple process, but it’s important to do it correctly to avoid damaging your refrigerator. In this article, we’ll walk you through the steps on how to reset the water filter on your Whirlpool refrigerator.

We’ll also provide some tips on how to maintain your water filter and keep your refrigerator running smoothly. So, if you’re ready to learn how to reset the water filter on your Whirlpool refrigerator, read on!

How To Reset Water Filter Whirlpool Fridge?

| Step | Action | Result |
|—|—|—|
| 1 | Turn off the water supply to the refrigerator. | |
| 2 | Locate the water filter housing. | It is usually located on the back of the refrigerator, near the bottom. |
| 3 | Remove the old water filter. | |
| 4 | Insert the new water filter. | Make sure that the filter is properly seated in the housing. |
| 5 | Turn on the water supply to the refrigerator. | |
| 6 | Run a glass of water through the filter. | This will help to flush out any air that may be trapped in the filter. |
| 7 | Enjoy your fresh, filtered water! | |

Step 1: Find the Water Filter

The water filter on a Whirlpool refrigerator is located in the back of the refrigerator, near the bottom. It is a cylindrical-shaped filter that is about 10 inches long and 3 inches in diameter. The filter is usually made of white plastic and has a blue cap.

To find the water filter, open the door to your refrigerator and look at the back of the refrigerator. The filter will be located in the upper left-hand corner of the back of the refrigerator.

Step 2: Turn Off the Power to the Refrigerator

Before you can replace the water filter, you need to turn off the power to the refrigerator. To do this, unplug the refrigerator from the wall outlet.

If your refrigerator is connected to a power strip, you can also turn off the power to the power strip.

Once you have turned off the power to the refrigerator, you can begin replacing the water filter.

Step 3: Remove the Old Water Filter

To remove the old water filter, grasp the cap of the filter and twist it counterclockwise. The filter will come out of the refrigerator.

Discard the old water filter.

Step 4: Insert the New Water Filter

To insert the new water filter, align the filter with the housing and twist it clockwise until it is snug.

The new water filter should be a snug fit in the housing. If the filter is not a snug fit, you may have inserted it incorrectly.

Step 5: Turn On the Power to the Refrigerator

Once you have inserted the new water filter, you can turn on the power to the refrigerator.

To do this, plug the refrigerator back into the wall outlet or turn on the power strip.

The refrigerator will take a few minutes to start up. Once the refrigerator is up and running, you can test the water filter to make sure it is working properly.

To test the water filter, run a glass of water through the water dispenser. The water should taste fresh and clean.

If the water does not taste fresh and clean, you may need to replace the water filter again.

Replacing the water filter in your Whirlpool refrigerator is a simple task that can be completed in just a few minutes. By following these steps, you can ensure that your refrigerator is properly filtered and that you are drinking clean, fresh water.

Step 3: Remove the Water Filter

To remove the water filter from your Whirlpool refrigerator, follow these steps:

1. Locate the water filter. The water filter is usually located in the door of your refrigerator, near the bottom. It is a cylindrical-shaped device with a blue cap.
2. Turn off the water supply to the refrigerator. This is usually located under the sink. Turn the valve clockwise until it is completely closed.
3. Unlock the water filter. There is a small button on the side of the water filter. Press this button to release the filter.
4. Remove the water filter. Grasp the water filter by the blue cap and twist it counterclockwise to remove it.
5. Discard the old water filter. The old water filter should be discarded in a recycling bin.

Step 4: Insert the New Water Filter

To insert the new water filter into your Whirlpool refrigerator, follow these steps:

1. Locate the water filter housing. The water filter housing is usually located in the door of your refrigerator, near the bottom. It is a cylindrical-shaped device with a blue cap.
2. Rinse the new water filter. Rinse the new water filter under cold water for a few seconds to remove any dust or debris.
3. Insert the new water filter. Insert the new water filter into the water filter housing. Make sure that the blue cap is facing up.
4. Lock the water filter. Press the button on the side of the water filter to lock it into place.
5. Turn on the water supply to the refrigerator. Turn the valve under the sink clockwise until it is completely open.
6. Wait for the water to run through the new water filter. The water should run clear before you use it.

By following these steps, you can easily remove and replace the water filter in your Whirlpool refrigerator. This will help to ensure that your refrigerator is properly filtered and that you are drinking clean, fresh water.

How do I reset the water filter on my Whirlpool fridge?

1. Locate the water filter. The water filter is usually located in the back of the fridge, near the bottom.
2. Turn off the water supply to the fridge. This is usually done by turning off the shut-off valve located under the sink.
3. Remove the old water filter. To do this, twist the filter counterclockwise until it comes loose.
4. Insert the new water filter. Make sure that the filter is properly seated in the housing.
5. Turn on the water supply to the fridge.
6. Press the “Reset” button on the water filter housing. This button is usually located on the front of the housing.
7. Run a glass of water through the water dispenser to flush out the new filter.

What happens if I don’t reset the water filter?

If you don’t reset the water filter, your fridge may not be able to filter the water properly. This could result in water that is not safe to drink, or that has a bad taste or smell.

How often do I need to reset the water filter?

The frequency with which you need to reset the water filter depends on the type of filter you have. Most filters need to be replaced every 6 months to 1 year.

What if I can’t find the water filter reset button?

If you can’t find the water filter reset button, consult your fridge’s owner’s manual. The manual will provide instructions on how to reset the water filter for your specific model of fridge.

Can I reset the water filter without turning off the water supply?

It is not recommended to reset the water filter without turning off the water supply. This could damage the water filter or the fridge.

What if I reset the water filter and the water still tastes bad?

If you reset the water filter and the water still tastes bad, there may be a problem with the water filter itself. You may need to replace the filter.

resetting the water filter on your Whirlpool fridge is a simple process that can be completed in just a few minutes. By following the steps outlined in this guide, you can ensure that your fridge is properly filtering your water and providing you with clean, refreshing water to enjoy.

Here are some key takeaways from this guide:

• The water filter on your Whirlpool fridge is located behind the kickplate at the bottom of the fridge.
• To reset the water filter, you will need to turn off the water supply to the fridge and remove the old filter.
• Once the old filter is removed, you can insert the new filter and turn the water supply back on.
• Your fridge will automatically begin to filter water again.

By following these steps, you can ensure that your Whirlpool fridge is properly filtering your water and providing you with clean, refreshing water to enjoy.