How To Adjust Headlights On Mazda 6?

How to Adjust Headlights on a Mazda 6

Your Mazda 6’s headlights are an important safety feature, but they can become misaligned over time. This can make it difficult to see at night and can also be a hazard to other drivers. If you notice that your headlights are pointing in different directions or that they’re not illuminating the road properly, it’s time to adjust them.

Adjusting your headlights is a relatively simple task that you can do yourself in just a few minutes. In this article, we’ll walk you through the process of adjusting your Mazda 6’s headlights so that they’re properly aligned.

We’ll also provide some tips on how to keep your headlights in good condition and how to troubleshoot common headlight problems. So whether you’re a new Mazda owner or you’re just looking for a refresher, read on for all the information you need to know about adjusting your headlights.

Step	Instructions	Image
1	Open the hood of your Mazda 6.
2	Locate the headlight adjustment screws. They are located on the back of the headlight assembly, near the top.
3	Turn the screws clockwise to raise the headlights or counterclockwise to lower them.
4	Once the headlights are adjusted to your satisfaction, close the hood of your Mazda 6.

Tools and Materials Needed

• Tape measure
• Phillips head screwdriver
• Flathead screwdriver
• Flashlight

Steps to Adjust Headlights

1. Park your Mazda 6 in a well-lit area.
2. Turn on your headlights and set the parking brake.
3. Locate the headlight adjustment screws. They are located on the back of the headlight assembly, near the top.
4. Use a Phillips head screwdriver to loosen the headlight adjustment screws.
5. Use a flashlight to look at the headlight beam pattern. The beam should be aimed at the center of the road, about 2 feet above the ground.
6. Adjust the headlight aim by turning the adjustment screws. Turn the screws clockwise to raise the beam and counterclockwise to lower the beam.
7. Tighten the headlight adjustment screws.
8. Test the headlight beam pattern by driving your Mazda 6 at night. The beam should be evenly distributed across the road.

Adjusting the headlights on your Mazda 6 is a simple task that can be completed in a few minutes. By following these steps, you can ensure that your headlights are properly aimed and that you are driving safely at night.

Here are some additional tips for adjusting your headlights:

• If you are not comfortable adjusting your headlights yourself, you can take your Mazda 6 to a qualified auto repair shop.
• Make sure to adjust your headlights after you have installed new headlights or replaced the headlight bulbs.
• If you live in an area with extreme weather conditions, you may need to adjust your headlights more frequently.

By following these tips, you can keep your Mazda 6 safe and ensure that you are properly visible to other drivers at night.

How to Adjust Headlights On Mazda 6?

Park your car in a dark area.

The first step is to park your car in a dark area. This will make it easier to see the beam pattern of your headlights and make adjustments as needed.

Turn on your headlights and open the hood.

Once you have parked your car in a dark area, turn on your headlights and open the hood. You will need to access the headlight adjustment screws, which are located on the back of the headlight housing.

Locate the headlight adjustment screws.

The headlight adjustment screws are located on the back of the headlight housing. There are two screws per headlight, one for vertical adjustment and one for horizontal adjustment.

Adjust the headlights.

To adjust the headlights, turn the screws clockwise to move the beam up and counterclockwise to move the beam down. To adjust the horizontal beam, turn the screws clockwise to move the beam to the left and counterclockwise to move the beam to the right.

Check the beam pattern.

Once you have adjusted the headlights, turn off your headlights and walk back to your car. Look at the beam pattern on the ground. The beam should be evenly distributed and should not be shining into oncoming traffic.

Re-adjust the headlights if necessary.

If the beam pattern is not correct, you will need to re-adjust the headlights. Repeat the steps above until the beam pattern is correct.

Adjusting your headlights is a simple task that can be completed in a few minutes. By following these steps, you can ensure that your headlights are properly adjusted and that you are not shining your headlights into oncoming traffic.

How do I adjust the headlights on my Mazda 6?

1. Turn on the headlights and find a dark area.
2. Park the car so that the front bumper is 25 feet (7.6 meters) from a wall.
3. Measure the distance from the ground to the center of the headlights.
4. Mark this spot on the wall with a piece of tape.
5. Turn off the headlights.
6. Open the hood and locate the headlight adjustment screws.
7. Turn the screws clockwise to raise the headlights or counterclockwise to lower them.
8. Turn on the headlights and check the beam pattern.
9. Adjust the headlights until the light is evenly distributed on the wall.
10. Turn off the headlights and close the hood.

What if my headlights are too high?

If your headlights are too high, they can blind other drivers and cause accidents. To lower your headlights, follow these steps:

1. Turn on the headlights and find a dark area.
2. Park the car so that the front bumper is 25 feet (7.6 meters) from a wall.
3. Measure the distance from the ground to the center of the headlights.
4. Mark this spot on the wall with a piece of tape.
5. Turn off the headlights.
6. Open the hood and locate the headlight adjustment screws.
7. Turn the screws counterclockwise until the headlights are level with the mark on the wall.
8. Turn on the headlights and check the beam pattern.
9. Adjust the headlights until the light is evenly distributed on the wall.
10. Turn off the headlights and close the hood.

What if my headlights are too low?

If your headlights are too low, they may not provide enough light for safe driving. To raise your headlights, follow these steps:

1. Turn on the headlights and find a dark area.
2. Park the car so that the front bumper is 25 feet (7.6 meters) from a wall.
3. Measure the distance from the ground to the center of the headlights.
4. Mark this spot on the wall with a piece of tape.
5. Turn off the headlights.
6. Open the hood and locate the headlight adjustment screws.
7. Turn the screws clockwise until the headlights are level with the mark on the wall.
8. Turn on the headlights and check the beam pattern.
9. Adjust the headlights until the light is evenly distributed on the wall.
10. Turn off the headlights and close the hood.

How often should I adjust my headlights?

You should adjust your headlights every time you replace the headlight bulbs or if you notice that the beam pattern is not correct.

In this blog post, we have discussed how to adjust the headlights on a Mazda 6. We have covered the steps involved in adjusting the headlights both manually and using the onboard computer. We have also provided some tips on how to make sure that your headlights are properly adjusted.

We hope that this information has been helpful. If you have any further questions, please do not hesitate to contact us.

Key Takeaways

• The headlights on a Mazda 6 can be adjusted manually or using the onboard computer.
• To adjust the headlights manually, you will need to use a screwdriver or wrench.
• To adjust the headlights using the onboard computer, you will need to access the vehicle’s infotainment system.
• The headlights should be adjusted so that they are aimed slightly downward.
• The headlights should be adjusted so that they are evenly distributed across the road.
• The headlights should be adjusted so that they do not blind oncoming traffic.